Look at the picture...
         __  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_ 
| | | |___|  _ \ / _ \ / _ \| __| 
| |_| |___| |_) | (_) | (_) | |_ 
 \___/    |____/ \___/ \___/ \__| 
 ** MARVELL BOARD: SHEEVA PLUG LE 

U-Boot 1.1.4 (Jul 19 2009 - 16:03:28) Marvell version: 3.4.19


U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CFB00

Soc: 88F6281 A0 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz 

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000   size 256MB 
DRAM CS[1] base 0x10000000   size 256MB 
DRAM Total size 512MB  16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:512 MB
Flash:  0 kB

CPU : Marvell Feroceon (Rev 1)

Streaming disabled 
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
Net:   egiga0 [PRIME], egiga1
Hit any key to stop autoboot:  0 
SDHC found. Card desciption is:
Manufacturer:       0x41, OEM "42"
Product name:       "SD4GB", revision 2.0
Serial number:      1526730671
Manufacturing date: 8/2009
CRC:                0x00, b0 = 0

2620504 bytes read
## Booting image at 00800000 ...
   Image Name:   Linux-2.6.30.2
   Created:      2009-07-23   1:53:36 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2620440 Bytes =  2.5 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK

Starting kernel ...

Uncompressing Linux.......................................................................................................................................................................... done, booting the kernel.
Linux version 2.6.30.2 (kelly@speedy) (gcc version 4.2.1) #11 PREEMPT Wed Jul 22 19:53:31 MDT 2009
CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
CPU: VIVT data cache, VIVT instruction cache
Machine: Marvell SheevaPlug Reference Board
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 130048
Kernel command line: console=ttyS0,115200 root=/dev/mmcblk0p2 rootdelay=5
NR_IRQS:114
PID hash table entries: 2048 (order: 11, 8192 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 256MB 256MB = 512MB total
Memory: 513408KB available (4728K code, 998K data, 140K init, 0K highmem)
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Calibrating delay loop... 1192.75 BogoMIPS (lpj=5963776)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 980 bytes
NET: Registered protocol family 16
Kirkwood: MV88F6281-A0, TCLK=200000000.
Feroceon L2: Enabling L2
Feroceon L2: Cache support initialised.
Kirkwood: Gating clock using mask 0x1ac224
bio: create slab  at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: US
	(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
	(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
	(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
	(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
	(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
	(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
	(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
cfg80211: Calling CRDA for country: US
NET: Registered protocol family 2
IP route cache hash table entries: 16384 (order: 4, 65536 bytes)
TCP established hash table entries: 65536 (order: 7, 524288 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 65536 bind 65536)
TCP reno registered
NET: Registered protocol family 1
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
JFS: nTxBlock = 4012, nTxLock = 32100
msgmni has been set to 1003
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
console [ttyS0] enabled
brd: module loaded
loop: module loaded
Driver 'sd' needs updating - please use bus_type methods
MV-643xx 10/100/1000 ethernet driver version 1.4
mv643xx_eth smi: probed
net eth0: port 0 with MAC address 00:50:43:01:64:34
libertas_sdio: Libertas SDIO driver
libertas_sdio: Copyright Pierre Ossman
NAND device: Manufacturer ID: 0xad, Chip ID: 0xdc (Hynix NAND 512MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 161 at 0x000001420000
Bad eraseblock 162 at 0x000001440000
Bad eraseblock 637 at 0x000004fa0000
Bad eraseblock 710 at 0x0000058c0000
Bad eraseblock 1040 at 0x000008200000
Bad eraseblock 1468 at 0x00000b780000
Bad eraseblock 1469 at 0x00000b7a0000
Bad eraseblock 1470 at 0x00000b7c0000
Bad eraseblock 2016 at 0x00000fc00000
Bad eraseblock 2932 at 0x000016e80000
Bad eraseblock 3607 at 0x00001c2e0000
Bad eraseblock 3608 at 0x00001c300000
Creating 3 MTD partitions on "orion_nand":
0x000000000000-0x000000100000 : "u-boot"
0x000000100000-0x000000500000 : "uImage"
0x000000500000-0x000020000000 : "root"
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
orion-ehci orion-ehci.0: Marvell Orion EHCI
orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
mice: PS/2 mouse device common for all mice
rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0
i2c /dev entries driver
cpuidle: using governor ladder
cpuidle: using governor menu
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
mmc0: mvsdio driver initialized, lacking card detect (fall back to polling)
Registered led device: plug:green:health
mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver
mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
mv_xor mv_xor.2: Marvell XOR: ( xor cpy )
mmc0: host does not support reading read-only switch. assuming write-enable.
mmc0: new high speed SDHC card at address 0007
mmcblk0: mmc0:0007 SD4GB 3.74 GiB 
 mmcblk0: p1 p2
mv_xor mv_xor.3: Marvell XOR: ( xor fill cpy )
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
oprofile: using timer interrupt.
TCP cubic registered
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
lib80211: common routines for IEEE802.11 drivers
rtc-mv rtc-mv: setting system clock to 2009-12-05 14:29:28 UTC (1260023368)
Waiting 5sec before mounting root device...
kjournald starting.  Commit interval 5 seconds
EXT3-fs warning: checktime reached, running e2fsck is recommended
EXT3 FS on mmcblk0p2, internal journal
EXT3-fs: mounted filesystem with writeback data mode.
VFS: Mounted root (ext3 filesystem) on device 179:2.
Freeing init memory: 140K
 * Filesystem type 'fusectl' is not supported. Skipping mount.
 * Setting preliminary keymap...                                         [ OK ] 
 * Starting kernel event manager...                                      [ OK ] 
 * Loading hardware drivers...                                           [ OK ] 
 * Loading kernel modules...                                                     
 * Loading manual drivers...                                             [ OK ] 
 * Setting kernel variables (/etc/sysctl.conf)...                        [ OK ] 
NET: Registered protocol family 10
ADDRCONF(NETDEV_UP): eth0: link is not ready
 * Setting kernel variables (/etc/sysctl.d/10-console-messages.conf)...  [ OK ] 
 * Setting kernel variables (/etc/sysctl.d/10-network-security.conf)...  [ OK ] 
 * Activating swap...                                                    [ OK ] 
 * Starting early crypto disks...                                        [ OK ] 
 * Starting remaining crypto disks...                                    [ OK ] 
 * Checking file systems...                                              
   fsck 1.41.4 (27-Jan-2009)                                             [ OK ]
 * Mounting local filesystems...                                         [ OK ] 
 * Activating swapfile swap...                                           [ OK ] 
 * Configuring network interfaces...                                     [ OK ] 
 * Setting up console font and keymap...                                 [ OK ] 
 * Starting system log daemon...                                         [ OK ] 
 * Starting kernel log daemon...                                         [ OK ] 

Ubuntu 9.04 gipserver4 ttyS0

 * Starting OpenBSD Secure Shell server sshd                             [ OK ]
 * Starting periodic command scheduler crond                             [ OK ] 
 * Starting web server apache2                                           [ OK ] 

Ubuntu 9.04 gipserver4 ttyS0

gipserver4 login: antonio
Password: 
Last login: Sat Dec  5 14:30:04 UTC 2009 from gipserver3.gameinprogress.com on pts/0
Linux gipserver4 2.6.30.2 #11 PREEMPT Wed Jul 22 19:53:31 MDT 2009 armv5tel

The programs included with the Ubuntu system are free software;
the exact distribution terms for each program are described in the
individual files in /usr/share/doc/*/copyright.

Ubuntu comes with ABSOLUTELY NO WARRANTY, to the extent permitted by
applicable law.

To access official Ubuntu documentation, please visit:
http://help.ubuntu.com/
antonio@gipserver4:~$ sudo shutdown -h now
[sudo] password for antonio:

Broadcast message from antonio@gipserver4
	(/dev/ttyS0) at 14:38 ...

The system is going down for halt NOW!
 * Stopping web server apache2                                           [ OK ]  ... waiting 
 * Saving the system clock
 * Asking all remaining processes to terminate...                        [ OK ] 
 * All processes ended within 2 seconds....                              [ OK ] 
 * Deconfiguring network interfaces...                                   [ OK ] 
 * Deactivating swap...                                                  [ OK ] 
 * Stopping remaining crypto disks...                                    [ OK ] 
 * Stopping early crypto disks...                                        [ OK ] 
 * Will now halt
halt: Unable to System halted.

Ex home page 1

Ex home page 2

Ex home page 3

Ex home page 4

Ex home page 5